目前分類:auto ecu programmer (24)
- Feb 26 Mon 2018 14:07
New Genius + Winols find VW Passat 1.9 pd 100 bhp maps
- Jan 19 Fri 2018 16:48
How to use Ktag 7.020 for Mercedes GL350 EDC17CP46
About: Chip-tuning Mercedes Benz GL350 3.0CDi 249 Hp 2015 with Ktag 7.020
Car: Mercedes Benz GL350 3.0CDi 249 Hp 2015
- Dec 05 Tue 2017 17:24
What is BDM Adapter & How to use?
KTAG KESS KTM BDM adapter Full Set is an electronic circuit intended for BDM operation on supported ECU. The adapter provides pogo pin based connectors for interfacing the ECU BDM connector. Interfacing the supported tool is made by the use of intermediate circuit board (multiplexer) that connects to the adapter over the MUX connector and to the tool over the desired tool connector (FGTECH, XPROG, BDM100,Dimsport, KTM100, Kess V2 & KTAG, etc.)
- Sep 20 Wed 2017 11:24
How to update KESS V2 FW 4.036 Ksuite 2.33 to Ksuite 2.35?
KESS V2 FW 4.036 Ksuite 2.33 update to latest Ksuite 2.35! Here is KESS V2 2.35 WIN XP installation guide!
Tested OK:
- Aug 17 Thu 2017 11:39
Ktag read Peugeot 407 SID803 (Pinouts)
This is how to read a 2004 Peugeot 407 SID803 ecu. Attach the BDM pinouts from the ribbon cable to the ecu and which ribbon cable to use for Ktag.
When you do not have an adapter you need to use a gray 10 pin cable to bdm. Pin it and solder the 5 wires, pin 1 is the one with the red line, then count it to 10 and solder according the picture by 1,5,6,7,8 pin (number one have red line), don't forget with power supply to the ecu.
- Jul 27 Thu 2017 15:35
MPPS V21 Tested OK: read ECU of Renault Megane 1.5
MPPS V21 software crack is tested successfully with the old MPPS V18 cable: read ECU ID data on Renault Megane 1.5 (106hp) DCi Siemens SID304 CAN.
This is how to read with MPPS v21:
- Jul 19 Wed 2017 09:56
R270 PCB Rework to Read/Write M35080
I played a few hours with my bad R270 programmer, and I succeeded to make it erase 35080V6/VP in a few minutes.
First I changed 7805 with L7805CV, before voltage was 4.94V, after that was 5.02V, but nothing happened, still can't erase more than hour.
- Jul 17 Mon 2017 16:51
How to update XPROG-M 5.55 firmware by Atmega64 repair chip?
In this blog you can: 1. Download XPROG-M Atmega64 dump. 2. Know Atmega64 repair chip update XPROG-M Box V5.55 firmware steps.
XPROG 5.55 flash Atmega64 Bin Hex free download for Xprog-M clone:
- Jul 11 Tue 2017 16:24
Xprog Box vs Xprog-M vs Xprog T vs Xprog
XPROG is an universal car ECU Programmer,supports more than 500 units, and the latest XPROG box 5.76 supports CAS4 5M48H and new adds other authorization, including: serial EEPROM's, Microcontrollers (MCU), Electronics Control Units (ECU), DashBoards, Immobilizers, Calculators and others).
XPROG --> XPROG-T --> Xprog-M --> XPROG BOX
- Oct 29 Sat 2016 14:11
Why should i buy Galletto 4, Kess v2 and Ktag together?
Kess v2, Ktag, Fgtech Galletto 4 are the top 3 ECU programmers in the market. Ever failed on some ECUs? Actually, it’s necessary to buy Kess , Ktag and Fgtech all together, especially for a pro. Reasons are listed here.
- Oct 10 Mon 2016 15:55
ECU tuning software: ECM TITANIUM vs WinOLS
Yes, I agree that WinOLS is advised to learn and use ECM TITANIUM not only, why? Because ecm is easier to use for people who start and how easy will be bad habit of using it as a single program.
- Aug 11 Thu 2016 15:41
Clone Carprog read MCU HC11E9 (wiring diagram)
- Aug 02 Tue 2016 17:17
How to rework Kess V2 hardware as the genuine
- Jul 29 Fri 2016 17:08
New Genius Master V5.05 or Kess V2 master V4.036?
With the newly released Genius Master V5.05 touch map, some people asked what it differs from Kess V2 master V4.036
Here is a comparison table made by www.obd2france.com engineer.
- Jul 25 Mon 2016 15:00
Carprog 8.21 change km for Skoda Yeti 2012 with nec&24c64
- Jul 22 Fri 2016 16:52
KESS V2 FW V4.036 add tokens - SUCCESS (personal experience)
I bought a KESS V2 Master Truck version with K-Suite 2.22 Firmware 4.036 online three months ago. When the tokens used up, I followed the guide video to add token and it was working. Here I will give a clear explanation of KESS token reset.
- Jul 22 Fri 2016 16:47
Carprog v8.21 100% read & write Opel CAN Siemens Simtec 71.6
Cool! Just succeed in reading and writing Opel CAN ECU Siemens Simtec 71.6 Advanced v0.7 with Carprog 8.21; i mean, i used this Carprog to change mileage. Share with you all.
- Jul 20 Wed 2016 14:17
How to use CANEMU CAN filter for Renault Laguna III, Megane III, Scenic III
This is the CANEMU CAN filter connection manual, which aimed to help use this CAN filter to prevent regeneration of the old mileage state in vehicle dashboard (odometer). CAN filter doesn’t interrupt any vehicle electronic system, there will be no errors or DTC’s after install. Now you can change mileage state with your preferred mileage correction tool on these Mercedes-Benz and Renault vehicles.
- Jul 20 Wed 2016 14:10
Comment faire pour installer New Genius K-touch ECU programmeur sur Win7 / XP 32 bits
What is New Genius?
New genius Clone is the world’s first Touch & Map device which allows reading / programming the ECU in modern vehicles over OBD2.It can work without connection a computer during the critical phases of reading and writing of the ECU.
- Jul 15 Fri 2016 17:45
CARPROG v8.21 USB PROGRAMMING (user solution)
This is a user experience to do Carprog 8.21 USB programming. Share it here.